FingerTec 3G Module
The FingerTec 3G module is ready to be used in models with FEM 800, which are TA200Plus (normal 12V model), Q2i and Face ID 2. Refer to the below table for technical specifications of the 3G module.
Technical Specifications | |
Frequencies | 2G/2.5G – GSM/GPRS/EDGE: Frequency - 850/900/1800/1900 MHz 3G – UMTS/HSPA Frequency – 850/1900/2100 MHz 3G – CDMA 2000 Frequency - 1900/2100 MHz |
Communication | Full duplex |
Automatic Startup | Yes |
Antenna Impedance | 50 Ohms |
SIM Card | 3 Volts (varies with SIM card) |
SIM Card PIN | Only reads the SIM card PIN, but cannot amend |
Receiver Parameters | |
GSM850 Reference Sensitivity | -104 dBm Static and TUHigh |
E-GSM900 Reference Sensitivity | -104 dBm Static and TUHigh |
DCS1800 Reference Sensitivity | -102 dBm Static and TUHigh |
PCS1900 Reference Sensitivity | -102 dBm Static and TUHigh |
Selectivity @ 200 kHz | > +9 dBc |
Selectivity @ 400 kHz | > +41 dBc |
Linear Dynamic Range | 63 dB |
Co-channel Rejection | >= 9 dBc |
Test Results
In our test, the 3G module works almost 40% faster than its predecessor (GPRS module) and, more importantly, is more stable.
Read more for instructions on how to install the 3G modules.
Installation of 3G Modules
Front view of 3G module
Back view of 3G module
For Q2i and TA200Plus:
Look closer to identify the location of the screw and the socket to plug in. This cable is only applicable in TA200Plus or Q2i.
For Face ID2:
Insert the module and antenna at the back cover of Face ID 2. Secure the antenna and module at their position.
Seek for the connectors at the MCU of Face ID 2. Plug in the cable from the 3G module as showed below. This cable is only applicable in Face ID 2.
Customized Firmware:
The devices require updating a customized firmware before they can start using the 3G module to link up to the Internet. For future orders, we will update the firmware before your shipment. However, you can also contact us at support@fingertec.com to collect the firmware if you would like to upgrade the device by yourself.
Related Articles
Integrate ZKTeco hardware to FingerTec Software (TCMS V3 or Ingress)
Introduction The capacity for two systems to work together without having to be altered, determine the matching of operating systems. It is common to come across compatibility issues due to a difference between the versions and/or different companies ...Diagnose Unstable Wi-Fi Connection on FingerTec Device
Introduction Wi-Fi is considered as one of the most required technological aspects for a modern lifestyle. As such, there are many Wi-Fi compatible devices offered in the market today that can connect to the Internet. That said, FingerTec likewise ...Fingertec TCMSv2 Installation Guide
Introduction TCMSv2 is a Windows-based software to manage the attendance data and generating the report to ease the human resource's work. Process 1) Download the TCMSv2 installer from this link: ...Fingertec TCMSv3 Installation Guide
Introduction TCMSv3 is built for the single user in order to manage the time attendance data in the organization. TCMSv3 is developed to replace the TCMSv2 software with the updated and fresh user interface to ease the user's experience in generating ...FAQs - FingerTec BioBridge SDK
Introduction FingerTec terminals come bundled with either the TCMSV2 or Ingress software for a Time Attendance system. Both software packages come as a complete system for all your time attendance and door access needs. However, for system developers ...