How To Setup TimeTec BLE-2 Without Modifying The EM-Lock Wirings
Introduction
In this link, we’ve described how to add TimeTec BLE-2 onto existing FingerTec Device. However, we received some feedbacks on whether is it possible to retain the arrangements of the EM-Lock wiring connection as well. This is to prevent the need of a new wiring as well as to assist in cost-saving.
Process
Hence in this article, we will explain how to add TimeTec BLE-2 without modifying the EM-Lock wirings. For this case, we will only require 4 cables to set up the wiring :
1. Two cables for power cable: +12V and GND.
2. Other two cables for Channel 1 Output: OUT 1 and COM.
The Channel 1 Output from TimeTec BLE-2 will be connected to the Button Input at the device. Therefore, when users access the door via TimeTec Security App, the Channel 1 Output will in turn be triggered. This output will then send the signal to the device thus unlocking the door. Refer to the diagrams below for more information.
To use this connection, we need to set TimeTec BLE-2 to Normally Open (NO) mode. You can configure this setting by looking at the right side of TimeTec BLE-2 and slide up the switch to enable Normally Open (NO) Mode.
Please take note that all transaction records from TimeTec BLE-2 are saved within TimeTec Security App only, and it will not be displayed on FingerTec Software or device.
Note: If some of the screenshots or steps viewed here are different from the ones in the current system, this is due to our continuous effort to improve our system from time to time. Please notify us at info@timeteccloud.com, we will update it as soon as possible.
In this link, we’ve described how to add TimeTec BLE-2 onto existing FingerTec Device. However, we received some feedbacks on whether is it possible to retain the arrangements of the EM-Lock wiring connection as well. This is to prevent the need of a new wiring as well as to assist in cost-saving.
Process
Hence in this article, we will explain how to add TimeTec BLE-2 without modifying the EM-Lock wirings. For this case, we will only require 4 cables to set up the wiring :
1. Two cables for power cable: +12V and GND.
2. Other two cables for Channel 1 Output: OUT 1 and COM.
The Channel 1 Output from TimeTec BLE-2 will be connected to the Button Input at the device. Therefore, when users access the door via TimeTec Security App, the Channel 1 Output will in turn be triggered. This output will then send the signal to the device thus unlocking the door. Refer to the diagrams below for more information.
Picture 1: Wiring diagram from TimeTec BLE-2
Picture 2: From TimeTec BLE-2 to FingerTec Device.
To use this connection, we need to set TimeTec BLE-2 to Normally Open (NO) mode. You can configure this setting by looking at the right side of TimeTec BLE-2 and slide up the switch to enable Normally Open (NO) Mode.
Picture 3 : Switch for TimeTec BLE-2 door lock type
Please take note that all transaction records from TimeTec BLE-2 are saved within TimeTec Security App only, and it will not be displayed on FingerTec Software or device.
Note: If some of the screenshots or steps viewed here are different from the ones in the current system, this is due to our continuous effort to improve our system from time to time. Please notify us at info@timeteccloud.com, we will update it as soon as possible.
Related Articles
Wiring Guide To Setup TimeTec BLE-2 With FingerTec Controller
Introduction Introducing TimeTec latest product: TimeTec BLE-2 Smart Door Controller which is a new technology for access door controller that brings convenience in unlocking doors as well as enhancing security. TimeTec BLE-2 uses Bluetooth Low ...Modifying Setup from Master-Master to Master-Slave
Before FingerTec Worldwide introduced Slave devices that could pair with Master devices, 2 master devices were used and modified to act as a Master-Slave setup for door access solution. Due to the distinct requirements by certain customers, the ...TA 200 Plus Wifi Setup
Introduction FingerTec offers an array of time attendance devices to fulfill the market's requirements. However, on top of the various selection, there are select devices customizable to the client's specific requirements such as adding a Wi-Fi. To ...How to Troubleshoot the Electromagnetic Lock/Door that Won’t Open
Introduction FingerTec Door Access readers can be paired with FingerTec AdapTec Plus/Adaptec X with electromagnetic locks to secure your premises’ door. These locks have a built-in safety feature that will disable the lock during emergencies. The ...Keylock 7700 – Interchangeable Lock Tongue
While designing FingerTec's Keylock 7700, we have taken into consideration not only the position of the lock (for left-handed or right-handed users) but also the installation of the door (either swing-in or swing-out method). FingerTec’s Keylock 7700 ...