Connecting the TA100C (FMM) to AdapTec TA and 12Vdc or 240Vac External Sirens
Introduction
The TA100C (FMM) is a biometric terminal for time attendance that includes an internal siren and allows the connection of external sirens for an effective alarm system. This system can also be scheduled to signal events within the working schedule such as starting work time or end of break.
The two types of sirens that can be connected to the TA100C (FMM) are:
a) 12Vdc for small industries or office use b) 240Vac for big factories with a noisy environment
Connecting your terminals to the Adaptec TA ensures a stable and reliable power source for your system to operate at optimum capacity. By connecting the terminal and external siren to the Adaptec TA, the internal relay of the terminal will be protected from the high voltage. If the voltage is too high, the fuse in Adaptec will break the circuit, thus protecting the internal components of the terminal.
Adaptec TA has 2 power sources, 5VDC and 12VDC and you can connect any of FingerTec terminals to Adaptec TA by selecting the correct voltage. It also comes with a backup power in case of power failure.
To connect the external siren to the terminal, follow the steps below.
1. Open the back casing of the TA100C (FMM) terminal.
2. Plug in the connector of the external siren into the MCU Board.
3. Follow the wiring diagram to connect the terminal to Adaptec TA.
4. Change the External Bell Relay settings in the terminal device itself.
Go to Menu > Personalize > Bell Schedule > Options > External Bell Relay > NC2
5. To add a new bell schedule, go to Menu > Personalize > Bell Schedules > New Bell Schedule > Set
the option accordingly:
the option accordingly:
· Bell Status: To turn the bell on or off.
· Bell Time: Set the time for the bell to ring automatically.
· Repeat: Set the bell to repeat on certain days or every day.
· Bell Type: You can set for the bell to be triggered from the internal bell or from an
external bell that is wired to the device.
external bell that is wired to the device.
· Ring Tone: Select your preferred ringtone that will emit from the bell.
· Internal Bell Relay: Specifies the time duration for the alarm to ring (ranges from 1s to999s).
· External Bell Relay: Specifies the time duration for the alarm to ring (ranges from 1s to999s).
Note: If some of the screenshots or steps viewed here are different from the ones in the current system, this is due to our continuous effort to improve our system from time to time. Please notify us at info@timeteccloud.com, we will update it as soon as possible.
Related Articles
Option to Connect an AC240V Siren with a FingerTec Device
The siren output signal from a FingerTec device is known as a dry contact and this basically means that the signal is not initially connected to a voltage source. It can also be referred to as a secondary set of contacts of a relay circuit, which ...Installation Guide of Face ID 4d (FMM) With AdapTec Plus
Introduction FingerTec Face ID 4D is now supplied with a new version of the coreboard (FMM) that comes with new hardware parts and new exterior parts. To ensure the reader connects with secured wiring, we suggest using the AdapTec Plus connection. ...Connecting the H2i with an AdapTec Plus
With the recent release of our new product AdapTec Plus, many might wonder what is the role of AdapTec Plus in supporting the terminal. The AdapTec plus is a combination of a power supply with enhanced access control functionalities. It supports ...Connecting External Bell to TA500
Introduction FingerTec TA500 is an affordable terminal to purchase; the investment cost is miniscule compared to the convenience and benefit it comes along with. This model can be customized to support External Schedule Bell, which is useful in ...Kadex External Siren
Introduction FingerTec’s Kadex terminal can be customised to support an external siren which is useful in alerting employees to make sure doors close properly after opening them to enter the premise or office. An external siren is also triggered when ...